Shop for American DJ V Power Amplifier and more at everyday discount prices with free shipping over $50* on – Your Online Store!. Buy the ADJ V Amplifier at PlanetDJ. Low VIP Pricing, Financing and Free Shipping available. American Audio | V | User manual | American Audio V User manual American Audio® – – V Vplus Series Amplifiers Power.
|Published (Last):||7 August 2016|
|PDF File Size:||18.58 Mb|
|ePub File Size:||8.36 Mb|
|Price:||Free* [*Free Regsitration Required]|
Although a speaker will operate with the positive and negative leads plugged into either v300 on the amplifier binding post, be sure to plug the negative lead into the black terminal and positive lead into Diagram 8 the red terminal.
The limiter reduces the average output level when the signal begins to distort, this process is designed to reduce distortion and protect the speakers. Red is positive signal and Black is negative signal. Each channel operates independently of each other allowing each channel to have different filter settings. If the input gain level is not reduced the built-in limiter will activate. Use channel two positive output terminal for the negative connection and the channel one positive output terminal for the positive connection.
Check the line from the output terminal of v0300 amplifier to the speaker. If the breaker continues to pop, stop using the amplifier and contact customer service. Circuit Breaker – This breaker is designed to protect the amplifier and aamerican speakers in the event of an AC overload.
American DJ V3000 2 Channel Professional Stereo Amplifier
This is to protect any speakers connected to the channel. When connecting your speakers to the amplifier using banana jacks; Be sure that the red and black caps on the binding post are tighten down completely. The speaker wire may be connect by bare wire directly connected, usually for permanent connectionsbanana plug, or spade connector.
The limiter has a fixed threshold and can not be adjusted. The dip switches on the rear panel allows you to enable or disable the filter for each channel, as well as adjust either a 50Hz or 30 Hz cut-off.
The XLR jack is configured as follows; Pin three positive, pin two negative, pin one ground. Amplifiers are shipped in stereo mode. Before using this amplifier, read the user manual for further warnings.
Gain Controls – The gain controls are located on the front panel and are calibrated in 2dB of attenuation from full gain. Cooling Vents – These vents are used for proper cooling. Connect your speakers to the outputs on the rear of the amplifier. Turn your equipment on your amplifier should always be the last item you turn on.
To prevent electrical shock or fire hazard, do not expose this amplifier to rain or moisture. Never block the fan in any way or mount in an enclose rack, doing so may cause the amplifier to overheat and fail. Connect your speaker across the red output binding post on the rear of your amplifier. To reduce the risk of electrical shock, do not remove cover.
A balanced connection is recommended for cable runs longer that 20ft. A limiter takes the gain of an overloading signal and reduces it, the reduction in gain reduces distortion that can cause damage to your speakers and amplifier. A short circuit will usually be traced to a bad cable or a bad speaker component and is rarely traced to the amplifier itself.
Insert the bare wire into the hole that was reveled by unscrewing the binding post cap.
Never plug your amplifier in to a wall outlet that does not match the required voltage of your ameerican, serious damage may occur to your unit. This light may amerian to glow briefly after main power has been turned off, this is normal. During excessive clipping the limiter will reduce the audio signal enough to minimize the amount of clipping.
The Output Short Circuit Protection protects the output devices of the amplifier from short circuits and stressful loads.
No user serviceable parts inside. Use your front gain controls rj regulate the output volume. Short Circuit Protection can usually be traced back to the signal output line i. Turn channel two gain up.
V Power Amplifier by American Audio Valuation Report by
Apply an input source signal to your amplifier. Typical speaker output using bare wire. Ground Lift Switch This switch is used to disconnect the internal ground signal from the amplifier chassis ground.
V30000 the input signal decreases enough that clipping ends, the limiter will deactivate and cease its gain reduction.
Never block the fan grills in any way or mount in an enclose rack, doing so may cause the amplifier to overheat and fail.
Every V Vplus series amplifier has been thoroughly tested and has been shipped in perfect operating condition.